Sena Parani-SD1000U User Manual Page 12
- Page / 49
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3. Configuration
3.1. Operation Modes
In addition to the serial port configurations the Parani-SD1000U also requires some settings for
Bluetooth. For getting the most out of Parani-SD1000U, user should understand the following
Bluetooth connection schemes.
A Bluetooth device can play a role as a master or slave. Master tries to connect itself to other
Bluetooth devices, and slave is waiting to be connected from other Bluetooth devices. A Bluetooth
connection is always made by a pair of master and slave devices. A slave can be in two modes,
Inquiry Scan or Page Scan mode. Inquiry Scan mode is waiting for a packet of inquiry from other
Bluetooth device and Page Scan mode is waiting for a packet of connection from other Bluetooth
device. Every Bluetooth device has its unique address, called BD (Bluetooth Device) address, which is
composed of 12 hexa-decimal numbers.
Parani-SD1000U has 4 operation modes as follows. Each mode can be identified with LED indicators
as illustrated in next section.
Table 3-1 The Parani-SD1000U Operation Modes
Mode
Description
Mode0
In this mode, there is no response when usb port connect or software reset, and Parani-
SD1000U is just waiting for AT command input. Neither master nor slave is assigned to
Parani-SD1000U in mode0. User can change the configuration parameters of Parani-
SD1000U in this mode.
Parani-SD1000U must be in Mode0, when it is directly controlled by AT commands.
The factory default is set to Mode0.
Mode1
Parani-SD1000U tries to connect the last connected Bluetooth device.
Parani-SD1000U in Mode1 is to be a master and tries to connect the last connected Bluetooth
device. Parani-SD1000U always stores the BD address of the Bluetooth device to which
Parani-SD1000U has connected last. When Parani-SD1000U is initially used or after hardware
reset, there is no BD address stored in Parani-SD1000U. In this case, Mode1 will not be able
to work properly. The mode change to Mode1 can be made after Parani-SD1000U succeeds
to connect to one other Bluetooth device. Once changed to Mode1, Parani-SD1000U will try to
connect automatically the last connected Bluetooth device whenever the unit is connect to usb
port or software reset.
Parani-SD1000U in Mode1 cannot be discovered or connected by other Bluetooth devices.
Mode2
Parani-SD1000U is waits for a connection from the last connected Bluetooth device.
Parani-SD1000U in Mode2 is to be a slave and waiting for the connection only from the last
connected Bluetooth device. Just like Mode1, if there is no BD address stored in Parani-
SD1000U, the mode change from other operation modes to Mode2 is not work properly. Once
changed to Mode2, Parani-SD1000U will wait for the connection from the last connected
Bluetooth device whenever the unit is connect to usb port or software reset.
Parani-SD1000U in Mode2 cannot be discovered or connected to Bluetooth devices other
than the last connected device.
Mode3
Parani-SD1000U is waiting for the connection from any other Bluetooth devices. In Mode 3 the
Parani-SD1000U is discoverable and can be connected to by other Bluetooth devices.
- Version 2.0.2 1
- 2012-01-18 1
- Copyright 2
- Trademark 2
- Notice to Users 2
- Technical Support 2
- Revision History 3
- Contents 4
- Appendix B: S-Register 41 5
- Appendix E: Warranty 48 6
- 1. Introduction 7
- Note *: 8
- 2. Getting Started 9
- 2.2.3. Virtual Serial Port 11
- 3. Configuration 12
- 3.2. LED Indicators 13
- 3.3. Serial Ports 13
- 3.4. Data Bit 13
- 3.5. Hardware Flow Control 13
- 3.7. Dipswitch 14
- 3.8. Pairing Button 15
- 3.9. Software and Utility 16
- 3.10. ParaniWIN 16
- 3.11. ParaniUpdater 22
- 3.12. Terminal Program 22
- 4. Multiple Connection Mode 24
- 4.2. Configuration 25
- 4.3. AT Commands 26
- 4.4. Notes 27
- 5. Approval Information 28
- 6. RF Information 29
- Appendix A: AT Commands 30
- A.2. Command Category 31
- A.3. Command Description 32
- A.3.6. AT+BTINFO? 33
- A.3.7. AT+BTINQ? 33
- A.3.8. AT+BTLAST? 33
- A.3.9. AT+BTVER? 33
- A.3.10. AT+MLIST? 33
- A.3.11. AT+BTMODE,n 34
- A.3.12. AT+MULTI,n 34
- A.3.13. +++ 34
- A.3.14. AT+SETESC,nn 34
- A.3.16. AT+BTCANCEL 35
- A.3.17. AT+BTSCAN 35
- A.3.18. AT+BTSCAN,n,to 35
- A.3.20. ATD 36
- A.3.21. ATD112233445566 36
- A.3.23. AT+BTKEY=$string 37
- A.3.24. AT+BTSD? 37
- A.3.25. AT+BTCSD 37
- A.3.26. AT+BTFP,n 37
- A.3.28. AT+BTNAME=$string 38
- A.3.29. AT+BTLPM,n 38
- A.3.31. AT&V 38
- A.4. Command Validity 39
- Appendix B: S-Register 41
- Appendix C: Trouble Shooting 46
- Appendix E: Warranty 48
Related products and manuals for Computer Accessories Sena Parani-SD1000U
Computer Accessories Sena LS110 User Manual
(66 pages)
(66 pages)
Computer Accessories Sena PS400 User Manual
(68 pages)
(68 pages)
Computer Accessories Sena HD1200 User Manual
(53 pages)
(53 pages)
Computer Accessories Sena LS100 User Manual
(48 pages)
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 0.944 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals